| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
nvs_config.{h,c} — persist the runtime config (viewport, scrypted,
idle_timeout_ms, orientation, brightness) under a single NVS namespace.
nvs_config_load() applies persisted values over the in-RAM defaults on
boot and flips state from UNCONFIGURED to ASLEEP once both name and
Scrypted URL are present. nvs_config_save() commits the whole record
atomically.
http_api.c — add GET /config and POST /config:
- GET serializes viewport_state to the spec's JSON shape, with null
for unset string fields and defaults filled in for the rest.
- POST is partial: each field is optional; only present fields are
validated and applied. Validation runs on a staged copy and errors
short-circuit with 400 + reason before any state mutation, so a
rejected request leaves the device untouched.
- Validation rules: viewport non-empty <64 chars; scrypted starts with
http:// and <256 chars; idle_timeout_ms 0 or >=5000; orientation in
{portrait,landscape}; brightness 0..100.
- Side-effects fire after the lock + save: brightness change pushes
PWM to the panel MCU; viewport/orientation change reapplies mDNS
hostname + TXT.
- 204 on success; 400 with a single-line reason on validation error.
app_main calls nvs_config_load() right after viewport_state_init(), so
mdns_service_start() and display_init() see the persisted hostname,
orientation, and brightness from the first packet/PWM.
Build clean against ESP-IDF 5.4 (binary ~620 KB).
TESTING.md M3 now documents the Hosyond jumper wiring (5V/GND/SDA=GPIO7/
SCL=GPIO8 from board to panel header; DSI FPC carries only the high-
speed lanes). M4 entry expands the validation matrix and side-effects
to verify.
|
|
display.{h,c} brings up the Hosyond 5\" 800x480 panel via the Raspberry
Pi 7\" touchscreen architecture:
- I2C init to the panel-side MCU at 0x45 (Pi 7\" register map ported
from drivers/gpu/drm/panel/panel-raspberrypi-touchscreen.c).
- POWERON write + 120ms settle.
- ESP32-P4 MIPI-DSI bring-up in DPI video mode: 2-lane, 480 Mbps,
800x480 @ 60Hz, RGB565, canonical Pi 7\" timings (HSW=18/HBP=20/HFP=62,
VSW=4/VBP=27/VFP=18, 30 MHz pixel clock).
- Gamma-corrected (^2.2) PWM brightness via REG_PWM (0x86).
- display_sleep / display_wake hooks for M6.
- display_fill() and display_test_pattern() (8 vertical color bars)
for M3 acceptance and reuse by M8 local screens.
app_main calls display_init() as best-effort — if the panel isn't
attached or wiring is wrong, the rest of the firmware (Ethernet, mDNS,
/state) keeps running. On success it paints the test pattern.
Pin assignments (PIN_I2C_SDA=7, PIN_I2C_SCL=8) match Waveshare's
bundled-panel BSP convention but are flagged TODO until the user's
specific FPC adapter wiring is confirmed.
main/CMakeLists.txt: add driver, esp_driver_i2c, esp_lcd to REQUIRES.
Build verified clean against ESP-IDF 5.4 for target esp32p4. M3
acceptance (color bars on screen) cannot be verified without a
flashed board + connected panel.
|
|
- viewport_state.{h,c}: shared state struct (config, run-state, counters,
orientation, timestamps) behind a FreeRTOS mutex. Modules update it
under viewport_state_lock(); GET /state serializes a snapshot.
- http_api.{h,c}: starts esp_http_server on :80, registers GET /state.
Returns the full JSON shape from the spec (name, version, configured,
state, uptime_ms, last_frame_ms_ago, frames_received, decode_errors,
state_post_failures, resolution, ip, free_heap, free_psram).
- mdns_service.{h,c}: mdns_init + advertise _scrypted-viewport._tcp.local
on :80 with version/resolution/orientation/name TXT records.
mdns_service_refresh() reapplies hostname + TXT after /config writes
(called from M4 onward).
- main/CMakeLists.txt: add esp_http_server, esp_timer, json, mdns to
REQUIRES. espressif/mdns added as managed component via
main/idf_component.yml.
app_main calls viewport_state_init early so any module can read defaults
before /config arrives.
Also adds TESTING.md tracking per-milestone verification status and an
integration test plan to run after M9 (races, failure modes, longevity,
power cycles, negative protocol, multi-viewport).
M1 promoted to "🟡 builds clean" in TESTING.md; combined HW verification
of M1+M2 will be one flash session. Build verified against ESP-IDF 5.4
for target esp32p4 (binary ~550 KB).
|
|
net_eth module brings up the Waveshare ESP32-P4-ETH-POE Ethernet
interface (internal EMAC + IP101GRI PHY) and waits for a DHCP lease.
Pin map confirmed via Waveshare wiki + ESPHome's working config:
MDC=31, MDIO=52, REF_CLK=50 (CLK_EXT_IN from PHY)
TX_EN=49, TXD0=34, TXD1=35
CRS_DV=28, RXD0=30, RXD1=29
PHY reset/enable=51, PHY addr=1
app_main initializes NVS, netif, the default event loop, then starts
the Ethernet driver and waits up to 30s for an IP. On success it logs
the IP; on timeout it logs a warning and proceeds (the driver keeps
retrying in the background).
sdkconfig: declare 16 MB flash so partitions.csv (6.1 MB) fits.
main/CMakeLists.txt: explicit REQUIRES esp_eth esp_event esp_netif
nvs_flash.
Acceptance (per M1 in the impl guide): device gets a DHCP lease over
Ethernet and prints its IP. Build is clean against ESP-IDF 5.4 for
target esp32p4.
|
|
|
|
Plain ESP-IDF project targeting Waveshare ESP32-P4-ETH-POE with a 5" 800x480
MIPI-DSI capacitive touch panel. Stub app_main with TODOs for Ethernet, mDNS,
HTTP API (/health, /config, /frame, /sleep, /brightness), JPEG decode, and
touch callback delivery per the v1 spec in README.md.
|
