|
jpeg_decoder.{h,c} wraps esp_driver_jpeg (ESP32-P4 hardware decoder).
- One-time engine + DMA-aligned PSRAM scratch buffer setup (1 MB input,
768 KB output @ panel native 800x480 RGB565).
- try_lock + unlock so concurrent /frame POSTs get 503 instead of
queueing, per spec.
- jpeg_decoder_get_info() reports the dimensions; the http handler
validates them against the effective resolution before painting.
display.h adds display_present_rgb565(src, w, h):
- Landscape: src is 800x480, memcpy 1:1 into the panel framebuffer.
- Portrait: src is 480x800, software rotate 90° CW into the 800x480
panel framebuffer. (PPA / 2D-DMA hardware rotation is a later
optimization if portrait latency matters.)
http_api.c adds POST /frame:
- Content-Type must be image/jpeg → else 400.
- Empty body → 400. > 1 MB → 413. Display not initialized → 500.
- jpeg_decoder_try_lock(0) for concurrency: second post returns 503.
- Body streamed into the decoder's input buffer in chunks.
- Decode failure or dimension mismatch → 400 + decode_errors++.
- Paint failure → 500.
- Success → frames_received++, last_frame_us = esp_timer_get_time(),
204 No Content.
app_main initializes the JPEG decoder after display_init(). Both are
best-effort: failures log a warning and leave the rest of the firmware
running.
CMakeLists.txt: add esp_driver_jpeg to REQUIRES.
Known gap (M6 closes it): /frame currently paints regardless of
wake/sleep state. The 409-when-asleep rule lands with POST /state
in M6.
Build clean against ESP-IDF 5.4 (binary ~640 KB).
TESTING.md M5 expanded with portrait/landscape test commands,
ImageMagick test-image recipes, the full negative matrix (wrong
Content-Type, oversize, wrong dims, concurrent, garbage), and the
M6 dependency note.
|
|
display.{h,c} brings up the Hosyond 5\" 800x480 panel via the Raspberry
Pi 7\" touchscreen architecture:
- I2C init to the panel-side MCU at 0x45 (Pi 7\" register map ported
from drivers/gpu/drm/panel/panel-raspberrypi-touchscreen.c).
- POWERON write + 120ms settle.
- ESP32-P4 MIPI-DSI bring-up in DPI video mode: 2-lane, 480 Mbps,
800x480 @ 60Hz, RGB565, canonical Pi 7\" timings (HSW=18/HBP=20/HFP=62,
VSW=4/VBP=27/VFP=18, 30 MHz pixel clock).
- Gamma-corrected (^2.2) PWM brightness via REG_PWM (0x86).
- display_sleep / display_wake hooks for M6.
- display_fill() and display_test_pattern() (8 vertical color bars)
for M3 acceptance and reuse by M8 local screens.
app_main calls display_init() as best-effort — if the panel isn't
attached or wiring is wrong, the rest of the firmware (Ethernet, mDNS,
/state) keeps running. On success it paints the test pattern.
Pin assignments (PIN_I2C_SDA=7, PIN_I2C_SCL=8) match Waveshare's
bundled-panel BSP convention but are flagged TODO until the user's
specific FPC adapter wiring is confirmed.
main/CMakeLists.txt: add driver, esp_driver_i2c, esp_lcd to REQUIRES.
Build verified clean against ESP-IDF 5.4 for target esp32p4. M3
acceptance (color bars on screen) cannot be verified without a
flashed board + connected panel.
|
